Full size Dalek robot made with Arduino and Adafruit Wave Shield #DrWho #arduino

NewImage

Thanks to Andy for sending in this awesome Dalek project! Read more on his blog here.

Soon after finishing my one-fifth scale Dalek Robot, I started work on a full size Dalek. This one is made from a combination of plywood, cardboard, PVC plumbing and acrylic Christmas decorations plus a good deal of duct tape and glue. Originally I made a paper mache dome but I couldn’t get it looking right so I cheated and purchased a fiber glass dome from a Dalek builder in the UK.

There have been many variations of the Dalek design on Doctor Who over the years and this one is based on those featured in the story “Genesis of the Daleks” with Tom Baker as the Doctor. These are the Daleks that I watched the most as child. Here’s a photo of the originals.

NewImage

Doctor Who was a low budget show at this time and the build quality of the Daleks wasn’t the best. Brush strokes can be seen in some shots and there is quite a bit of variance between individual Daleks, so I chose to take some liberties with my interpretation (and cut many a corner to keep time and cost to a minimum).

When I started out on the project I had grand ambitions for turning this into a robot as well but I haven’t made that happen yet. Instead I have installed an Arduino and an Adafruit wave shield that I can use either as a voice changer or I can have it play sound clips that I downloaded from the Doctor Who web site.

Here’s a video of the voice changer in action.

Read more.


Featured Adafruit Product!

NewImage

Adafruit Wave Shield for Arduino Kit: Adding quality audio to an electronic project is surprisingly difficult. Here is a shield for Arduinos that solves this problem. It can play up to 22KHz, 12bit uncompressed audio files of any length. It’s low cost, available as an easy-to-make kit. It has an onboard DAC, filter and op-amp for high quality output. Audio files are read off of an SD/MMC card, which are available at nearly any store. Volume can be controlled with the onboard thumbwheel potentiometer. Read more.


Adafruit publishes a wide range of writing and video content, including interviews and reporting on the maker market and the wider technology world. Our standards page is intended as a guide to best practices that Adafruit uses, as well as an outline of the ethical standards Adafruit aspires to. While Adafruit is not an independent journalistic institution, Adafruit strives to be a fair, informative, and positive voice within the community – check it out here: adafruit.com/editorialstandards

Join Adafruit on Mastodon

Adafruit is on Mastodon, join in! adafruit.com/mastodon

Stop breadboarding and soldering – start making immediately! Adafruit’s Circuit Playground is jam-packed with LEDs, sensors, buttons, alligator clip pads and more. Build projects with Circuit Playground in a few minutes with the drag-and-drop MakeCode programming site, learn computer science using the CS Discoveries class on code.org, jump into CircuitPython to learn Python and hardware together, TinyGO, or even use the Arduino IDE. Circuit Playground Express is the newest and best Circuit Playground board, with support for CircuitPython, MakeCode, and Arduino. It has a powerful processor, 10 NeoPixels, mini speaker, InfraRed receive and transmit, two buttons, a switch, 14 alligator clip pads, and lots of sensors: capacitive touch, IR proximity, temperature, light, motion and sound. A whole wide world of electronics and coding is waiting for you, and it fits in the palm of your hand.

Have an amazing project to share? The Electronics Show and Tell is every Wednesday at 7pm ET! To join, head over to YouTube and check out the show’s live chat – we’ll post the link there.

Join us every Wednesday night at 8pm ET for Ask an Engineer!

Join over 36,000+ makers on Adafruit’s Discord channels and be part of the community! http://adafru.it/discord

CircuitPython – The easiest way to program microcontrollers – CircuitPython.org


Maker Business — “Packaging” chips in the US

Wearables — Enclosures help fight body humidity in costumes

Electronics — Transformers: More than meets the eye!

Python for Microcontrollers — Python on Microcontrollers Newsletter: Silicon Labs introduces CircuitPython support, and more! #CircuitPython #Python #micropython @ThePSF @Raspberry_Pi

Adafruit IoT Monthly — Guardian Robot, Weather-wise Umbrella Stand, and more!

Microsoft MakeCode — MakeCode Thank You!

EYE on NPI — Maxim’s Himalaya uSLIC Step-Down Power Module #EyeOnNPI @maximintegrated @digikey

New Products – Adafruit Industries – Makers, hackers, artists, designers and engineers! — #NewProds 7/19/23 Feat. Adafruit Matrix Portal S3 CircuitPython Powered Internet Display!

Get the only spam-free daily newsletter about wearables, running a "maker business", electronic tips and more! Subscribe at AdafruitDaily.com !



No Comments

No comments yet.

Sorry, the comment form is closed at this time.