IN STOCK! Raspberry Pi Model B+

1914-01

IN STOCK! Raspberry Pi Model B+ OMG OMG OMG, did you hear? There is a brand new Raspberry Pi! And this one’s called the Model B+ and check it out…more USB ports, more GPIO, better power supply, four mounting holes, less sticky-out SD card! Yep, that’s right, the fantastic engineers at Raspberry Pi HQ have blessed us with a new design. They’ve taken all the feedback over the last 3 years and rolled out a nice updated Pi with many fixes and extras…all at the same price!

1914-04

Take a deep breath and buckle up, because Adafruit has this freshness and we’re going to break it down for you. We have a big tutorial that we’re keeping updated, with all the nitty-gritty details, so check that out when you have a moment

1914-02

Here’s a brief overview of what’s new:

  • Dual step-down (buck) power supply for 3.3V and 1.8V
  • 5V supply has polarity protection, 2A fuse and hot-swap protection (so you can plug/unplug USB without resetting the board)
  • New USB/Ethernet controller chip
  • 4 USB ports instead of 2 ports
  • 40 GPIO pins instead of 26. The top/first 26 pins match the original layout, 9 additional GPIO and 2 EEPROM Plate identification pins
  • Composite (NTSC/PAL) video now integrated into 4-pole 3.5mm ‘headphone’ jack
  • MicroSD card socket instead of full size SD
  • Four mounting holes in rectangular layout
  • Many connectors moved around

1914-03

What’s not new:

  • Same basic size, 85mm x 56mm
  • Same Processor, Broadcom SoC running at 700MHz (can be overclocked)
  • Same RAM, 512MB soldered on top of the Broadcom chip
  • Same power connector, microUSB
  • Same software – be sure to run the latest Raspbian/NooBs but otherwise the overall Linux software is the same
  • First 26-pins of GPIO are the same
  • Same HDMI port
  • Audio part of the A/V jack is the same
  • Same Camera and DSI Display connector

1914-00

So, basically, its the same single-board Linux computer you’ve known and loved but all cleaned up and easier to use. The good news is many of your existing accessories like cables, hubs, keyboards, monitors, etc will work fine. Many Pi Plates (PCBs that plug into GPIO port directly) will also work.

However 26-pin GPIO cables do not fit this means that you cannot use classic Cobblers, GPIO-cabled boards like the GertBoard/PermaProtoPi without a GPIO downgrading cable. Model B cases will not fit the B+, the cases must be redesigned for the B+ as so much has moved around! You also need to be running Raspbian or NooBs from after approx June 2014 since earlier ones do not have USB/Ethernet chipset support.

We’ll have more accessories for the B+ such as cases, Cobblers, and more very soon!

  • PCB Dimensions: 56mm x 85mm x 1.4mm / 2.2″ x 3.4″ x 0.06″
  • Height with USBs: 17mm / 0.7″
  • Weight: 42g
  • Mechanical Schematic

Connector Schematic
Mechanical Schematic
Raspberry Pi Model B+ specs

IN STOCK AND SHIPPING NOW!


Adafruit publishes a wide range of writing and video content, including interviews and reporting on the maker market and the wider technology world. Our standards page is intended as a guide to best practices that Adafruit uses, as well as an outline of the ethical standards Adafruit aspires to. While Adafruit is not an independent journalistic institution, Adafruit strives to be a fair, informative, and positive voice within the community – check it out here: adafruit.com/editorialstandards

Join Adafruit on Mastodon

Adafruit is on Mastodon, join in! adafruit.com/mastodon

Stop breadboarding and soldering – start making immediately! Adafruit’s Circuit Playground is jam-packed with LEDs, sensors, buttons, alligator clip pads and more. Build projects with Circuit Playground in a few minutes with the drag-and-drop MakeCode programming site, learn computer science using the CS Discoveries class on code.org, jump into CircuitPython to learn Python and hardware together, TinyGO, or even use the Arduino IDE. Circuit Playground Express is the newest and best Circuit Playground board, with support for CircuitPython, MakeCode, and Arduino. It has a powerful processor, 10 NeoPixels, mini speaker, InfraRed receive and transmit, two buttons, a switch, 14 alligator clip pads, and lots of sensors: capacitive touch, IR proximity, temperature, light, motion and sound. A whole wide world of electronics and coding is waiting for you, and it fits in the palm of your hand.

Have an amazing project to share? The Electronics Show and Tell is every Wednesday at 7pm ET! To join, head over to YouTube and check out the show’s live chat – we’ll post the link there.

Join us every Wednesday night at 8pm ET for Ask an Engineer!

Join over 36,000+ makers on Adafruit’s Discord channels and be part of the community! http://adafru.it/discord

CircuitPython – The easiest way to program microcontrollers – CircuitPython.org


Maker Business — “Packaging” chips in the US

Wearables — Enclosures help fight body humidity in costumes

Electronics — Transformers: More than meets the eye!

Python for Microcontrollers — Python on Microcontrollers Newsletter: Silicon Labs introduces CircuitPython support, and more! #CircuitPython #Python #micropython @ThePSF @Raspberry_Pi

Adafruit IoT Monthly — Guardian Robot, Weather-wise Umbrella Stand, and more!

Microsoft MakeCode — MakeCode Thank You!

EYE on NPI — Maxim’s Himalaya uSLIC Step-Down Power Module #EyeOnNPI @maximintegrated @digikey

New Products – Adafruit Industries – Makers, hackers, artists, designers and engineers! — #NewProds 7/19/23 Feat. Adafruit Matrix Portal S3 CircuitPython Powered Internet Display!

Get the only spam-free daily newsletter about wearables, running a "maker business", electronic tips and more! Subscribe at AdafruitDaily.com !



1 Comment

  1. What is the Run Pad? – a reset switch?
    The ethernet leds (link/100mb) have moved to the connector as all modern connectors!

Sorry, the comment form is closed at this time.