How To Build A Solar Heater With Soda Cans #SolarPower

Build a solar heater with soda cans. by John Horning via fair companies

Building a solar panel heater out of aluminum cans is not as far-fetched as you might think. A company in Canada, Cansolair, Inc., specializes in building these units and has won awards for their design.

Their heaters have been described as “green energy and recycling all rolled into one”, and have proven to be very cost effective and efficient as well.

How do they work

The units are typically installed on the outside walls of houses, and of course, in a location that gets a lot of sun. The idea is to draw air from near the floor of any room in a home, and pass it through the heating panel, which contains several columns of cans.

The air is then returned to the same room near the ceiling. The cans are stacked and have large holes cut in both ends to allow the air to pass inside them while the outside of the cans is getting hot from the sun.

What you’ll need

240 aluminum cans.
3 – 8 ft. 2x4s.
4 ft. x 8 ft. x 1/2 in. sheet of plywood.
High temperature silicon.
4 ft. x 8 ft. sheet of Plexiglas or Lexan.
A can of heat-resistant flat black spray paint.
Plastic tubing.
Drill Press with wide drill bits.
Screws.
Optional Air Blower (consider a solar-powered unit).
How to build the solar panel

Construct a wooden frame out the the 2x4s, approx. 4 ft. wide x 8 ft. high x 3 1/2 in. deep. Next cut a piece of plywood this size and nail it to the back of the frame.
Drill a hole in the top center of the frame – this is where you’ll connect your outlet hose.
Drill a hole in the bottom of the frame – this is where your inlet hose will be connected.
Drill large holes in the tops and bottoms from all the cans except for 16 which will be on the bottom row. For those, drill the holes in the tops and sides. Caution! Aluminum cans are sharp – use heavy work gloves or other means to hold them in place as you cut the hols out.
Start placing your cans into the frame. Create 16 columns of 15 cans each. Stack them one at at time, sealing them together as you go along. Make sure the ones with side holes are on the bottom row. Allow the silicone sealant to cure.
Spray the cans and frame with the heat-resistant flat black paint.
Cover the frame with the sheet of Plexiglas or Lexan.
Cut holes in the side of the building that line up with holes in the top and bottom of the solar panel. Air will be drawn from the building through the lower hole, which should be just above floor level, and be returned through the upper hole.
Mount the completed panel on the exterior wall of the home. Alternatively, you might mount the panel in a separate frame that will allow it to be tilted more toward the sun for better exposure.
Install the blower at either the inlet or outlet. This is not essential, but will increase the efficiency of your solar heater.
This unit allows air to flow all around the cans as it moves through the panel. A more efficient design will force all the air through the inside of the cans. This will also avoid exposure of the air to the black paint.

Read more


Adafruit publishes a wide range of writing and video content, including interviews and reporting on the maker market and the wider technology world. Our standards page is intended as a guide to best practices that Adafruit uses, as well as an outline of the ethical standards Adafruit aspires to. While Adafruit is not an independent journalistic institution, Adafruit strives to be a fair, informative, and positive voice within the community – check it out here: adafruit.com/editorialstandards

Join Adafruit on Mastodon

Adafruit is on Mastodon, join in! adafruit.com/mastodon

Stop breadboarding and soldering – start making immediately! Adafruit’s Circuit Playground is jam-packed with LEDs, sensors, buttons, alligator clip pads and more. Build projects with Circuit Playground in a few minutes with the drag-and-drop MakeCode programming site, learn computer science using the CS Discoveries class on code.org, jump into CircuitPython to learn Python and hardware together, TinyGO, or even use the Arduino IDE. Circuit Playground Express is the newest and best Circuit Playground board, with support for CircuitPython, MakeCode, and Arduino. It has a powerful processor, 10 NeoPixels, mini speaker, InfraRed receive and transmit, two buttons, a switch, 14 alligator clip pads, and lots of sensors: capacitive touch, IR proximity, temperature, light, motion and sound. A whole wide world of electronics and coding is waiting for you, and it fits in the palm of your hand.

Have an amazing project to share? The Electronics Show and Tell is every Wednesday at 7pm ET! To join, head over to YouTube and check out the show’s live chat – we’ll post the link there.

Join us every Wednesday night at 8pm ET for Ask an Engineer!

Join over 36,000+ makers on Adafruit’s Discord channels and be part of the community! http://adafru.it/discord

CircuitPython – The easiest way to program microcontrollers – CircuitPython.org


Maker Business — “Packaging” chips in the US

Wearables — Enclosures help fight body humidity in costumes

Electronics — Transformers: More than meets the eye!

Python for Microcontrollers — Python on Microcontrollers Newsletter: Silicon Labs introduces CircuitPython support, and more! #CircuitPython #Python #micropython @ThePSF @Raspberry_Pi

Adafruit IoT Monthly — Guardian Robot, Weather-wise Umbrella Stand, and more!

Microsoft MakeCode — MakeCode Thank You!

EYE on NPI — Maxim’s Himalaya uSLIC Step-Down Power Module #EyeOnNPI @maximintegrated @digikey

New Products – Adafruit Industries – Makers, hackers, artists, designers and engineers! — #NewProds 7/19/23 Feat. Adafruit Matrix Portal S3 CircuitPython Powered Internet Display!

Get the only spam-free daily newsletter about wearables, running a "maker business", electronic tips and more! Subscribe at AdafruitDaily.com !



No Comments

No comments yet.

Sorry, the comment form is closed at this time.