New Raspberry Pi camera mode released @Raspberry_Pi #raspberrypi

NewImage

Raspberrypi.org has sorted out a new set of mode for their camera board. They are also calling for pictures and video using the new mode and will feature the best entries on their site!

When the Raspberry Pi camera was released, the eagle-eyed among you noticed that the camera hardware itself can support various high frame rate modes, but that the software could ‘only’ manage 30 frames per second in its high-definition video mode.

There’s is no hardware limitation in the Raspberry Pi itself. It’s quite capable of handling these high frame rate modes, but it does require a certain amount of effort to work out these new ‘modes’ inside the camera software. At the original release of the camera, two modes were provided: a stills capture mode, which offers the full resolution of the sensor (2592×1944), and a 1080p video mode (1920x1080p). Those same eagle-eyed people will see that these modes have different aspect ratios – the ratio of width to height. Stills outputs 4:3 (like 35mm film), video 16:9 (wide screen).

This creates a problem when previewing stills captures, since the preview uses the video mode so it can run at 30 frames per second (fps) – not only is the aspect of the preview different, but because the video mode ‘crops’ the sensor (i.e. takes a 1920×1080 windows from the centre), the field of view in preview mode is very different from the actual capture.

We had some work to do to develop new modes for high frame rates, and also fix the stills preview mode so that is matches the capture mode.

So now, finally, some very helpful chaps at Broadcom, with some help from Omnivision, the sensor manufacturer, have found some spare time to sort out these modes, and not just that but to add some extra goodness while they were at it. (Liz interjects: The Raspberry Pi Foundation is not part of Broadcom – we’re a customer of theirs – but we’ve got a good relationship and the Foundation’s really grateful for the volunteer help that some of the people at Broadcom offer us from time to time. You guys rock: thank you!)

The result is that we now have a set of mode as follows :

  • 2592×1944 1-15fps, video or stills mode, Full sensor full FOV, default stills capture
  • 1920×1080 1-30fps, video mode, 1080p30 cropped
  • 1296×972 1-42fps, video mode, 4:3 aspect binned full FOV. Used for stills preview in raspistill.
  • 1296×730 1-49fps, video mode, 16:9 aspect , binned, full FOV (width), used for 720p
  • 640×480 42.1-60fps, video mode, up to VGAp60 binned
  • 640×480 60.1-90fps, video mode, up to VGAp90 binned

I’ve introduced a new word in the that list. Binned. This is how we can get high frame rates. Binning means combining pixels from the sensor together in a ‘bin’ in the analogue domain. As well as reducing the amount of data, this can also improve low light performance as it averages out sensor ‘noise’ in the absence of quantisation noise introduced by the analogue to digital converters (ADCs), which are the bits of electronics in the sensor that convert the analogue information created by incoming photons to digital numbers.

Read more.


Featured Adafruit Product!

NewImage

Raspberry Pi Camera Board – The Raspberry Pi Camera Module is a custom designed add-on for Raspberry Pi. It attaches to Raspberry Pi by way of one of the two small sockets on the board upper surface. This interface uses the dedicated CSI interface, which was designed especially for interfacing to cameras. The CSI bus is capable of extremely high data rates, and it exclusively carries pixel data. Read more.



Adafruit publishes a wide range of writing and video content, including interviews and reporting on the maker market and the wider technology world. Our standards page is intended as a guide to best practices that Adafruit uses, as well as an outline of the ethical standards Adafruit aspires to. While Adafruit is not an independent journalistic institution, Adafruit strives to be a fair, informative, and positive voice within the community – check it out here: adafruit.com/editorialstandards

Join Adafruit on Mastodon

Adafruit is on Mastodon, join in! adafruit.com/mastodon

Stop breadboarding and soldering – start making immediately! Adafruit’s Circuit Playground is jam-packed with LEDs, sensors, buttons, alligator clip pads and more. Build projects with Circuit Playground in a few minutes with the drag-and-drop MakeCode programming site, learn computer science using the CS Discoveries class on code.org, jump into CircuitPython to learn Python and hardware together, TinyGO, or even use the Arduino IDE. Circuit Playground Express is the newest and best Circuit Playground board, with support for CircuitPython, MakeCode, and Arduino. It has a powerful processor, 10 NeoPixels, mini speaker, InfraRed receive and transmit, two buttons, a switch, 14 alligator clip pads, and lots of sensors: capacitive touch, IR proximity, temperature, light, motion and sound. A whole wide world of electronics and coding is waiting for you, and it fits in the palm of your hand.

Have an amazing project to share? The Electronics Show and Tell is every Wednesday at 7pm ET! To join, head over to YouTube and check out the show’s live chat – we’ll post the link there.

Join us every Wednesday night at 8pm ET for Ask an Engineer!

Join over 36,000+ makers on Adafruit’s Discord channels and be part of the community! http://adafru.it/discord

CircuitPython – The easiest way to program microcontrollers – CircuitPython.org


Maker Business — “Packaging” chips in the US

Wearables — Enclosures help fight body humidity in costumes

Electronics — Transformers: More than meets the eye!

Python for Microcontrollers — Python on Microcontrollers Newsletter: Silicon Labs introduces CircuitPython support, and more! #CircuitPython #Python #micropython @ThePSF @Raspberry_Pi

Adafruit IoT Monthly — Guardian Robot, Weather-wise Umbrella Stand, and more!

Microsoft MakeCode — MakeCode Thank You!

EYE on NPI — Maxim’s Himalaya uSLIC Step-Down Power Module #EyeOnNPI @maximintegrated @digikey

New Products – Adafruit Industries – Makers, hackers, artists, designers and engineers! — #NewProds 7/19/23 Feat. Adafruit Matrix Portal S3 CircuitPython Powered Internet Display!

Get the only spam-free daily newsletter about wearables, running a "maker business", electronic tips and more! Subscribe at AdafruitDaily.com !



No Comments

No comments yet.

Sorry, the comment form is closed at this time.