Using Arduino in Bread Making at Home

BreadRising

Using Arduino in Bread Making at Home from Mental Masala.

“Let rise at room temperature” is a common instruction in bread recipes, with “room temperature” being about 70 F (21.1 C)*. For various reasons, however, this temperature can be hard to find in my apartment in Berkeley, California, and so my bread doughs sometimes rise far too slowly.

One day, I realized that my Arduino Uno microcontroller could help solve this problem.  I had earlier configured it to measure milk temperature during yogurt making, and realized that would be a short leap to use it to control the air temperature inside a container, thereby creating a stable and warm location for dough fermentation and proofing (a “proofing box”).  My idea was simple: an incandescent light bulb in a clip-on lamp as the heat source, a temperature sensor, a switch that turns the light bulb on and off, and the Arduino to control the switch. Basically, as one person who heard my plan put it, “It’s an Easy-Bake Oven!”

But how would I switch the light bulb on and off using the low voltage, low current digital outputs on the Arduino? A relay could be wired in and the lamp could be hacked, but that would be bothersome and potentially dangerous.  Then I learned about the Powerswitch Tail II. This easy-to-use device allows your Arduino or other controller to switch on and off an A/C powered device, like a lamp, coffee maker, hot plate, and so on. By connecting a digital output line and ground from the Arduino to the + and – inputs of the Powerswitch Tail, the connected device can be switched on and off. No cutting, soldering or taping required, just connect and go…..

Read more.

HowItWorks


Featured Adafruit Product!

NewImage

Powerswitch tail 2: The Power Switch Tail II is a smart alternative to slicing apart power cords to wire up your own relays. Its a compact 120V 3-pronged extension cord, with a relay board embedded in the middle. Connect to the relay using two screw terminals and activate by providing a 3 to 12V signal (3mA current draw at 3V, 30mA at 12V). The relay can switch 15 Amp resistive loads such as heaters, small skillets, lights, etc. An LED indicator above the terminals will help you with debugging. (read more)


Adafruit publishes a wide range of writing and video content, including interviews and reporting on the maker market and the wider technology world. Our standards page is intended as a guide to best practices that Adafruit uses, as well as an outline of the ethical standards Adafruit aspires to. While Adafruit is not an independent journalistic institution, Adafruit strives to be a fair, informative, and positive voice within the community – check it out here: adafruit.com/editorialstandards

Join Adafruit on Mastodon

Adafruit is on Mastodon, join in! adafruit.com/mastodon

Stop breadboarding and soldering – start making immediately! Adafruit’s Circuit Playground is jam-packed with LEDs, sensors, buttons, alligator clip pads and more. Build projects with Circuit Playground in a few minutes with the drag-and-drop MakeCode programming site, learn computer science using the CS Discoveries class on code.org, jump into CircuitPython to learn Python and hardware together, TinyGO, or even use the Arduino IDE. Circuit Playground Express is the newest and best Circuit Playground board, with support for CircuitPython, MakeCode, and Arduino. It has a powerful processor, 10 NeoPixels, mini speaker, InfraRed receive and transmit, two buttons, a switch, 14 alligator clip pads, and lots of sensors: capacitive touch, IR proximity, temperature, light, motion and sound. A whole wide world of electronics and coding is waiting for you, and it fits in the palm of your hand.

Have an amazing project to share? The Electronics Show and Tell is every Wednesday at 7pm ET! To join, head over to YouTube and check out the show’s live chat – we’ll post the link there.

Join us every Wednesday night at 8pm ET for Ask an Engineer!

Join over 36,000+ makers on Adafruit’s Discord channels and be part of the community! http://adafru.it/discord

CircuitPython – The easiest way to program microcontrollers – CircuitPython.org


Maker Business — “Packaging” chips in the US

Wearables — Enclosures help fight body humidity in costumes

Electronics — Transformers: More than meets the eye!

Python for Microcontrollers — Python on Microcontrollers Newsletter: Silicon Labs introduces CircuitPython support, and more! #CircuitPython #Python #micropython @ThePSF @Raspberry_Pi

Adafruit IoT Monthly — Guardian Robot, Weather-wise Umbrella Stand, and more!

Microsoft MakeCode — MakeCode Thank You!

EYE on NPI — Maxim’s Himalaya uSLIC Step-Down Power Module #EyeOnNPI @maximintegrated @digikey

New Products – Adafruit Industries – Makers, hackers, artists, designers and engineers! — #NewProds 7/19/23 Feat. Adafruit Matrix Portal S3 CircuitPython Powered Internet Display!

Get the only spam-free daily newsletter about wearables, running a "maker business", electronic tips and more! Subscribe at AdafruitDaily.com !



No Comments

No comments yet.

Sorry, the comment form is closed at this time.